Plastic Condensation Trays, Containment Trays, Drip Trays and Pans

We use the vacuum thermoforming to make condensation, containment trays. We begin with a flat sheet of plastic and form it either into or over a mold. This process stretches and thins the material while creating the Three Dimensional shape. This is why we state the “Beginning Gauge” of a product. You should expect the part to be strong but somewhat thinner than the beginning gauge stated.

We stock some of these trays and or can do a run of them quickly, in any quantity you need. If our "stock" Condensation trays, Containment trays, or Drip Trays are not perfect for your application, give us a call. We can custom fabricate trays for you!

Our Condensation trays, Containment trays, or Drip Trays care custom and made from chemically resistant plastics and are seal tight. We make trays that are light weight, strong, and self supporting, if needed, and are easily shipped. We can create trays of any size, shape or thickness. We can also add fiberglass reinforcing for strength and heat resistance.

We can make up simple soft tooling for trays to help meet your requirements. Please call today!
Tray 1
This tray was developed for small refrigerators to set in.
Specs:
Cavity depth: 1” Deep
Dimensions:

18” X 19” I.D. This is the flat surface available to set a piece of equipment on.
18-9/16” X 20-1/8” O.D. This is the largest width and length.
Made with Black Textured one side ABS plastic with a beginning thickness
of .093” (3/32”)
Tray 2
This tray developed for hanging over head to catch oil drips falling from a conveyor system.
Specs:
Cavity depth: ½” Deep
Dimensions:

16” X 30” I.D. This is the flat surface available to set a piece of equipment on.
16-3/4” X 30-5/8” This is the largest width and length of the flange of the tray.
Made with Black Textured one side ABS plastic with a beginning thickness
of .093” (3/32”)
Tray 3
This tray was developed to meet a wide range of applications.
Specs:
Cavity depth: 3/4” Deep
Dimensions:

18-7/8” X 24-7/8” I.D. This is the flat surface available to set a piece of equipment on.
20” X 26” This is the largest width and length of the flange of the tray.
Made with Black Textured one side ABS plastic with a beginning thickness
of .093” (3/32”)
Tray 4
This tray developed to catch oil drips and condensation from printing presses.
Specs:
Cavity depth: ½” Deep
Dimensions:

24-1/8” X 32” I.D. This is the flat surface available to set a piece of equipment on.
25-1/4” X 33-1/4” This is the largest width and length of the flange of the tray.
Made with Black Textured one side ABS plastic with a beginning thickness
of .062” (1/16”)

Locker Trays

ShapeMaster stands ready to develop a custom tray to meet your needs.

Consider these for lockers and applications where you may need to store boots and shoes that are wet, mud or snow covered.

Note: we use the vacuum thermoforming process to make our trays. We begin with a flat sheet of plastic and form it either into or over a mold. This process stretches and thins the material while creating the Three Dimensional shape. This is why we state the “Beginning Gauge” of a product. You should expect the part to be strong but some what thinner than the beginning gauge stated.
Locker Tray
Designed for school lockers to keep those shoes and boots that collect snow from melting and running down into the lockers. This not only contains water neatly but mud as well.
Specs:
Cavity depth: 1-1/8” Deep
Dimensions:

10” X 10-3/4” I.D. this is the flat surface available to set the boots on.
10-5/8” X 11-1/2” O.D. this is the largest width and length of the tray a the top edge.
Made with Black Textured one side ABS plastic with a beginning thickness of .903” (3/32”).


 Plastic Cavity Trays | Plastic Pistol Grips | Plastic Electronic Enclosures | Condensation Trays